android
  #1  
Old 03-18-2011, 03:53 AM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default HiFiMan HM-601 review and test

Hi all,

I'm new on this forum. It looks like a pretty interesting place. I thought I'd contribute some information, perhaps someone will find it interesting.

I'm an engineer and a musician. Recently I bought the HiFiMan HM-601 to use with my relatively high impedance headphones. I thought it had some interesting features, and, truth be told, the whole audiophile thing had an effect on me, although I'm usually very skeptical.

I bought it online and thought some music sounded very good on it, and some sounded kind of strange. I'm not going to say anything about the design. The battery life is poor, user interface very buggy, but I'm not going to dwell on that, either. It's supposed to be about the sound. Again, I didn't think that everything sounded right on it, but these things can be pretty subtle and difficult to judge.

Then I found this forum and an extremely long thread about the HM-801, which is now closed. In essence, the HM-801 has a noticeable roll-off at high frequencies, and somewhere in that thread Fang (the designer, as far as I understood) explained that it sounded less digital that way. I thought it was a pretty strange claim, and the most likely explanation not involving black magic was that it had some digital artifacts, which the roll-off helped to hide. I decided to test my HM-601 against other devices, using RMAA.

DUT:

HM-601, firmware v0.04
Sansa Clip+, firmware 1.02.15A
iPod 5.5, Rockbox 2.7.1

Sorry if iPods are not allowed on this forum.

Test ADC: M-Audio FW-410.

Test software: RMAA 6.2.3

The test signal was recorded as a 44.1 kHz, 16-bit wav file for the iPod and the HM-601, and converted as a 256 kbps mp3 for the Sansa, which was running native firmware and did not seem to support wav.

The frequency response of the HM-601 is very similar to that of HM-801. The other devices exhibit a flat response, as expected.



Perhaps, this roll-off sounds "less digital". The question is why. I think the plot below illustrates the problem:



These are the spectra of the 1-kHz sinusoidal signal, which is played by the DUTs at approximately the same level. It's the part of the test protocol that is supposed to measure the THD. Note the 2nd harmonic of the Sansa, by the way. Most noticeable of course are the peaks at every 100 Hz in the HM-601 output signal, which are clearly not harmonics but digital artifacts.

Here are the same data plotted from 0 to approximately 3.5 kHz.



The HM-601 has similar problems at 10 kHz, although the pattern is a little more complicated and the spacing is not 100 Hz. I think these artifacts are probably much more audible at higher fundamental frequencies, to use the term loosely.



I'm not sure where these artifacts are coming from; most likely, poorly implemented resampling.

All of the tests above were done at 44.1 kHz, 16 bit mode for the RMAA ADC input, but the results are similar at other sampling frequencies and bit depths. Output levels were approximately matched between iPod and HiFiMan. RMAA has its share of problems, apparently, but I'm reasonably sure that these results accurately reflect the DUT performance.

I was already thinking of returning this magical audiophile player because of numerous other flaws, these results did not make me want to keep it.

It took several emails to figure out the address to send it to, but I got the refund very quickly. Just as I was returning it, they came out with a new minor firmware release, 0.05, which I did not try.

Sergei

Last edited by sergivs; 03-18-2011 at 07:49 AM. Reason: typos
Reply With Quote

Advertisement [Remove Advertisement]

  #2  
Old 03-18-2011, 07:34 AM
dfkt's Avatar
dfkt dfkt is offline
Moderator
 
Join Date: May 2006
Location: Vienna, Austria
Posts: 15,330
Default

Very interesting, thanks for the post. That looks quite a bit worse than the already flawed 801.

We have a thread about the 602, which is basically the same hardware as the 601 - especially the second part of this post might be interesting to you: http://www.anythingbutipod.com/forum...8&postcount=33
__________________
Please don't PM me with questions that can be answered in a forum thread. Don't be an idiot.
My Gear and Reviews | My RMAA Tests | IRC: #anythingbutipod on Freenode | Last.fm | Album Art Exchange | Rockbox | Replaygain
Reply With Quote

  #3  
Old 03-18-2011, 08:14 AM
WalkGood's Avatar
WalkGood WalkGood is offline
Moderator
 
Join Date: Aug 2006
Location: FL
Posts: 12,579
Default

Quote:
Originally Posted by sergivs View Post
Hi all, I'm new on this forum. ...
Hi Sergei and welcome to abi, thanks for the post … What kills me is how they continue to defend the hifiman, even though the 601 is lower priced ($259.00) it’s still overpriced considering bad UI, buggy firmware, bad battery life and no better sq than players 1/5 it’s price *cough* Sansa Clip
__________________
WalkGood,
Ramůn

abi >> | Forum Rules | Glossary | Why Rockbox | FLAC or MP3? | irc
Reply With Quote

  #4  
Old 03-18-2011, 08:21 AM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default

Quote:
Originally Posted by dfkt View Post
We have a thread about the 602, which is basically the same hardware as the 601 - especially the second part of this post might be interesting to you: http://www.anythingbutipod.com/forum...8&postcount=33
Thanks, I actually did see that thread after I posted this one. It's very interesting. I would think that oversampling in the sense that's described there would be more useful in an ADC than a DAC, at least in a portable audio player DAC, but I'm not an expert in this area, but I digress, anyway. I think the main point is the same, the "hi-end" hi-end roll-off seems to be used to sweep digital artifacts under the rug. So, apparently, that's particular to the DAC chip. That's pretty interesting.

Too bad I did not find this forum earlier, would have never bought the stupid thing.

BTW the 1-kHz sine is one of the few different THD tests in the RMAA protocol.

Last edited by sergivs; 03-18-2011 at 08:30 AM. Reason: clarification
Reply With Quote

  #5  
Old 03-18-2011, 08:24 AM
Marvin the Martian's Avatar
Marvin the Martian Marvin the Martian is offline
Ultra Senior Member
 
Join Date: Oct 2008
Location: east central NY state
Posts: 10,602
Default

Quote:
Originally Posted by WalkGood View Post
Hi Sergei and welcome to abi, thanks for the post Ö What kills me is how they continue to defend the hifiman, even though the 601 is lower priced ($259.00) itís still overpriced considering bad UI, buggy firmware, bad battery life and no better sq than players 1/5 itís price *cough* Sansa Clip
Maybe because they are one of the sponsors, like NuForce? lol
__________________
iPod Touch 5G 32GB, Touch 4G 32GB, Clip Sport 8GB. Rockbox-> Clip Zip 4GB, iPod Nano 2G 4GB, iPod 5.5G 80GB
2012 Nexus 7 32GB, Asus MeMoPad 8 16+64GB, LG Optimus G Pro, Nokia Lumia 900 and Lumia 520
Reply With Quote

  #6  
Old 03-18-2011, 08:37 AM
The DarkSide's Avatar
The DarkSide The DarkSide is offline
Ultra Senior Member
 
Join Date: Feb 2008
Location: Qns Vlg, NYC
Posts: 16,039
Default

I agree, as the main & most argumentative individuals are also the idiots marketing the poorly made and overpriced devices.

Anyways, welcome to ABI sergivsi, and thanks for the great info.

PS: there's nothing wrong w/discussion of iPods here, but the preference is for alternative TO the iPod - and there seems to be less & less lately.
Reply With Quote

  #7  
Old 03-18-2011, 09:36 AM
odigg odigg is offline
Member
 
Join Date: Dec 2008
Posts: 134
Default

Hilarious!

The best part is now they have to stick to their flawed design since they responded with "You listen to your ears, not a scope" and "Ours sound the best." If they "improve (read: fix)" it they are basically admitting their current design is flawed and will have to run away with their tail between their legs.

Didn't the Hifiman representative basically say they were mimicking the sound of some Wadia eqiupment? Does Wadia have these same artifacts?

Here are some measurements of a Wadia CD Player from Stereophile

I'll let somebody who is more technically competent with these matters make an evaluation.
Reply With Quote

  #8  
Old 03-18-2011, 12:28 PM
sideways sideways is offline
Senior Member
 
Join Date: Mar 2010
Posts: 590
Default

Welcome to abi and thanks for a great first post! No comment on my part about that craptastic player beyond I'm glad you got your money back.
Reply With Quote

  #9  
Old 03-18-2011, 01:26 PM
Satellite_6's Avatar
Satellite_6 Satellite_6 is offline
Senior Member
 
Join Date: Feb 2009
Location: VA, USA
Posts: 871
Default

Interesting! I'm not sure I understand them completely but those graphs are pretty scary looking. . .
__________________
satelliteaudioblog.blogspot.com

Last edited by Satellite_6; 03-18-2011 at 02:44 PM.
Reply With Quote

  #10  
Old 03-18-2011, 02:44 PM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default

Quote:
Originally Posted by odigg View Post
Didn't the Hifiman representative basically say they were mimicking the sound of some Wadia eqiupment? Does Wadia have these same artifacts?

Here are some measurements of a Wadia CD Player from Stereophile
If I remember correctly, Fang just used this player as an example of something that sounds great and yet has a high-frequency roll-off.

This article does not seem to have a comparable measurement, i.e. the spectrum of a high-level, single-frequency signal reproduction. I'd be surprised if it showed the same artifacts, but who knows.

There is a frequency response plot in part 1 of that article. The roll-off is actually not as strong: -3 dB at 20 kHz vs -5 dB in the HiFiMan. The author writes that his hearing cuts off at 16 kHz and that he "only very occasionally felt that the Wadia's highs sounded dull", which sounds questionable. But my hearing cuts off at 17 kHz, at least it did about a year ago, and I actually might be able to tell the difference that the HiFiFiMan roll-off makes. Not sure.

Here's his explanation for the roll-off: "Wadia's DigiMaster reconstruction filter sacrifices both initial stop-band attenuation and upper passband response to achieve its goal of optimal time-domain behavior." This all sounds very mysterious; I think by "optimal time-domain behavior" he means the absence of ringing, although the beauty of using language like that is that your readers can never be completely sure what you mean, so you don't have to be, either.

RMAA does not have an impulse-response or a square-wave test, unfortunately, which would show the ringing. I found an interesting blog recently, which has the square-wave test results for iPod touch and Sansa Clip+, I think. In light of the above it would be interesting to see the HiFiMan measurements as well, but it's too late now.

Last edited by sergivs; 03-18-2011 at 02:51 PM. Reason: typo
Reply With Quote

  #11  
Old 03-18-2011, 03:04 PM
skip252 skip252 is offline
Administrator
 
Join Date: Dec 2007
Location: Chicago
Posts: 5,200
Default

My understanding of quite a few of those audio terms is limited. I found this explanation for the lack of a flat response by Nankai. Can anyone tell me if the application of the filter he mentions would have the same effect?
Reply With Quote

  #12  
Old 03-18-2011, 03:37 PM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default

Quote:
Originally Posted by skip252 View Post
My understanding of quite a few of those audio terms is limited. I found this explanation for the lack of a flat response by Nankai. Can anyone tell me if the application of the filter he mentions would have the same effect?
The short answer is yes. The slightly longer answer is: it might, depending on the choice cut-off frequency.

In this thread so far we are using general signal-processing terms, I think.

I don't think the roll-off itself is necessarily that big a deal. It may be a sign of bigger problems, though. For example, in the post that you link to the premise is that there is digital noise that they need to get rid of. What kind of digital noise? Where is it coming from?
Reply With Quote

  #13  
Old 03-18-2011, 04:05 PM
skip252 skip252 is offline
Administrator
 
Join Date: Dec 2007
Location: Chicago
Posts: 5,200
Default

That's part of what confused me. He seemed to be saying the digital signal itself would be "high freq" noise. Given that a digital to audio converter (DAC) would be needed. I would think that one would be chosen that would result in the cleanest audio signal possible.

He then states that a signal like that with out filtering would be "digital sounding" which is why they added they Butterworth filter. I really wanted to find if your tests had any way to determine if the rolloff and distortions were the addition of that filter or just hardware that's not up to the job of producing a clean signal.

Once again please forgive any misunderstandings of basic audio theory I may exhibit in how I phrase this. I'm very new to this and am studying up on it but there's a number of things I know I still don't have a clear understanding on.
Reply With Quote

  #14  
Old 03-18-2011, 05:07 PM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default

Quote:
Originally Posted by skip252 View Post
That's part of what confused me. He seemed to be saying the digital signal itself would be "high freq" noise. Given that a digital to audio converter (DAC) would be needed. I would think that one would be chosen that would result in the cleanest audio signal possible.
It's not very clear what he's saying about "hi freq". In the simplest case, the DAC should not produce any audible high-frequency noise. Maybe somehow in practical applications and in some designs it's can be a problem, I can think of a couple of scenarios, but I really don't know. Filtering is definitely critical before an ADC, but that is a different story.

Quote:
Originally Posted by skip252 View Post
He then states that a signal like that with out filtering would be "digital sounding" which is why they added they Butterworth filter. I really wanted to find if your tests had any way to determine if the rolloff and distortions were the addition of that filter or just hardware that's not up to the job of producing a clean signal.
Roll-off, yes, distortions, no. Those are digital artifacts, and they are not normal, and are not present in a well-designed system. One possible reason why they had to use a relatively low cut-off frequency is to make them less noticeable (even if they did not realize what they were dealing with). That was my guess. Or maybe they were trying to get rid of ringing and these artifacts are a coincidence. But they don't look good and I'm pretty sure don't always sound good.

Quote:
Originally Posted by skip252 View Post
Once again please forgive any misunderstandings of basic audio theory I may exhibit in how I phrase this. I'm very new to this and am studying up on it but there's a number of things I know I still don't have a clear understanding on.
Why apologize? This is an interesting and complicated subject.

I'm not an audio specialist myself and do not know some of the subtleties, which can be very interesting; but at least I have a little practical knowledge and a pretty solid understanding of the basic theory. And, unfortunately, it seems that many people writing on the subject, especially promoting some product, don't even have that, or are trying to confuse the matter. Such is life.
Reply With Quote

  #15  
Old 03-18-2011, 05:45 PM
skip252 skip252 is offline
Administrator
 
Join Date: Dec 2007
Location: Chicago
Posts: 5,200
Default

Thanks for the information. The one thing I've found as I've been looking onto picking up something about audio is that it tends to follow a logical progression. I kept trying to connect the dots in that statement and I just couldn't make any sense of it. If it also throws someone that has a better understanding of theory I don't feel as bad.
Reply With Quote

  #16  
Old 03-18-2011, 07:05 PM
musichound musichound is offline
Off-Topic Moderator
 
Join Date: Jun 2007
Location: Staten Island, NYC
Posts: 2,058
Default

I find this advertisement hilarious:

http://www.headphone.com/accessories...601-player.php

Quote:
Originally Posted by Deceiving HiFiMan HM601 ad:
Blows away typical MP3 player sound quality
__________________
Cowon X7 160GB - iRiver H320 - IPod Classic 160GB - iPod 5.5G 80GB - Sansa Clip Plus 4GB - Original Sansa Clip 2GB
Reply With Quote

  #17  
Old 03-18-2011, 10:30 PM
lestatar's Avatar
lestatar lestatar is offline
Ultra Senior Member
 
Join Date: Dec 2009
Location: Hong Kong now, but NYC always
Posts: 4,657
Default

@sergivs: Great great post and indeed welcome to ABi!

In many ways I think I am like skip252 on these matters, though perhaps I am slightly less industrious I am familiar with most of the terminology but only have an extremely rudimentary understanding - I cannot say I have any real comprehension of many of these concepts. Still, I do find this stuff interesting.

Your comment about people really not understanding many aspects of the products they are selling/marketing made me laugh out loud - it just so happens that this is exactly the situation I find myself involved in for the time being in HK.

Thanks so much for the post and the work you put in - stuff like this simply re-affirms my belief that the HyFyMan gear just ain't for me [and never will be].

cheers!
-les
__________________
DAPs:2xRBFuze8+16GB|SonyE345|ZenV+,Micro,Xtra40GBx2|RBG igabeatFX|RCAOpal
IEMs:PanaHJE900|Nuforce 700x|HippoVB|iMetal590,i490|SM PL-21|CX300|EP630,Aurvana
Guitars:IbanezS540,JS1200|Ovation
PoolCues: a bunch
A Glossary for Newbies
Reply With Quote

  #18  
Old 03-19-2011, 01:57 AM
sergivs sergivs is offline
Junior Member
 
Join Date: Mar 2011
Posts: 67
Default

Thanks everyone, I'm glad you found this little experiment interesting, and I'm glad I found this forum. I'll ask some questions later.
Reply With Quote

  #19  
Old 03-19-2011, 05:34 AM
Jack4L's Avatar
Jack4L Jack4L is offline
Ultra Senior Member
 
Join Date: Sep 2006
Location: Finland
Posts: 1,511
Default

Welcome to the forums, always interesting to read such detailed (well for a forum post ) analysis.

Kinda weird that their firmware is 0.04, implying that they aren't ready to call the product finished, yet they're selling it. Well, maybe that just piques potential buyers with hopes of "It'll become even better!" and its not like larger companies sell fully finished products at launch.

In any case its nice to hear you got your refund, I mean its the least they can do but you still gotta give them credit for it.
Reply With Quote

  #20  
Old 03-22-2011, 06:46 AM
Shike Shike is offline
Junior Member
 
Join Date: Sep 2010
Posts: 7
Default

Quote:
Originally Posted by Marvin the Martian View Post
Maybe because they are one of the sponsors, like NuForce? lol
Is there something specifically wrong with NuForce? I know their potentiometers on some portable DAC/Amps have problems with highly sensitive IEMs . . . ?
Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 08:55 PM.